Aumenta ou diminui o brilho geral de uma imagem.
Este módulo tem dois modos de operação:
- manual
- Set the exposure and black level manually
- automático (somente imagens em RAW)
- Faz uma análise do histograma da imagem para estabelecer automaticamente a exposição. O Ansel seleciona automaticamente a compensação de exposição necessária para alterar o percentil selecionado ao nível alvo selecionado (consulte as definições abaixo). Este modo é particularmente útil para alterar automaticamente uma grande quantidade de imagens para que tenham a mesma exposição. Um caso de uso típico do modo automático é no processamento de fotografias de time-lapse (para evitar o efeito de cintilação).
Module controls
- Mode
- Choose the mode of operation (automatic/manual).
- Compensate camera exposure (manual mode)
- Automatically remove the camera exposure bias (taken from the image’s Exif data).
- Exposure (manual mode)
- Increase (move to the right) or decrease (move to the left) the exposure value (EV). To adjust by more than the default limits shown on the slider, right click and enter the desired value up to +/-18 EV.
- The color picker on the right sets the exposure such that the average of the sampled region matches the target lightness defined in the spot exposure mapping options. The first time it is turned on, it samples nearly the whole image. Then click in the image to sample a point, or drag to sample a rectangular area.
- While the module has the focus, holding Ctrl (⌘ on macOS) and clicking or dragging in the image samples in the same way without turning the picker on. See picking colors on the image.
- Percentile (automatic mode)
- Define a location in the histogram to use for automatic exposure correction. A percentile of 50% denotes a position in the histogram where 50% of pixel values are above and 50% of pixel values are below that exposure.
- Target level (automatic mode)
- Define the target level for automatic exposure correction (EV) relative to the white point of the camera.
- Black level correction (manual and automatic modes)
- Adjust the black level point to unclip negative RGB values.
Note: Do not use the black level correction to add more density in blacks as this can clip near-black colors out of gamut by generating negative RGB values. This can cause problems with some modules later in the pixelpipe. Instead, use a tone mapping curve to add density to the blacks. For example, you can use the relative black exposure slider on the scene tab of the filmic rgb module.
Spot exposure mapping
The spot mapping feature is designed to help with batch-editing a series of images in an efficient way. In this scenario, you typically develop a single reference image for the whole batch and then copy&paste the development stack to all of the other images in the batch.
Infelizmente, a luz geralmente muda um pouco entre as fotos, mesmo dentro da mesma série capturada nas mesmas condições. Isso pode ser o resultado de uma nuvem passando pelo sol em luz natural, reflexos de superfície com menos “brilho” de um ângulo diferente, ou simplesmente devido à variabilidade inevitável na abertura mecânica do diafragma. Cada imagem ainda precisará de alguns ajustes individuais se você quiser uma visão perfeitamente uniforme de toda a série, e isso pode ser demorado e frustrante.
O mapeamento de exposição pontual permite definir um brilho alvo, em termos de exposição, para uma determinada região da imagem (a amostra de controle), que você compara com o mesmo brilho alvo em outras imagens. A amostra de controle pode ser uma parte crítica do seu assunto que precisa ter brilho constante ou uma superfície imóvel e iluminada de forma consistente na sua série de imagens.
O processo de mapeamento consiste de dois passos.
Step 1: set the target
Existem duas maneiras de definir o brilho alvo para sua amostra de controle:
- If you know or expect an arbitrary lightness for the control sample (for example, a gray card, a color chart, a product or a logo of a specified brightness), you can set its L value directly, in CIE Lab 1976 space,
- If you simply want to match the development of your reference image, set the spot mode to measure, then enable the color picker (to the right of the exposure slider) and click on your control sample, or draw a rectangle over it. The input column will then be updated with the lightness value of the control sample before the exposure correction, and the target column will show the resulting lightness of the control sample after the current exposure setting is applied.
Se você redefinir o valor de luminosidade, o valor padrão será 50% (cinza médio) – isso pode ser útil para definir rapidamente a exposição média de qualquer imagem.
Note que o valor alvo não é redefinido quando você redefinir o próprio módulo, mas é armazenado indefinidamente na configuração do Ansel e estará disponível no próximo lançamento do aplicativo, bem como para a próxima imagem que você processar.
Step 2 : match the target
When you open a new image, the spot mode is automatically reset to correction. Using the color picker attached to the exposure slider, or holding Ctrl (⌘ on macOS) and clicking in the image, you can then directly reselect your control sample in the new image. The proper exposure setting required for the control sample to match the memorized target lightness will be automatically computed, and the setting will be updated in the same operation.
Esta operação pode ser repetida tantas vezes quanto forem as imagens em sua série sem outro trabalho adicional.
Nota 1: Tentar combinar a luminosidade de partes móveis de um assunto em tomadas diferentes pode ser complicado porque elas podem ter mudanças legítimas em sua iluminação à medida que sua orientação muda em relação à fonte de luz principal. Por exemplo, uma parte do rosto pode ser totalmente iluminada em algumas fotos e parcialmente sombreada em outras. Uma amostra de controle com iluminação inconsistente geralmente não fornecerá uma referência robusta para correspondência de luminosidade em uma série e pode resultar em mais trabalho do que combiná-la manualmente com feedback visual.
Note 2: The exposure module works (by default) in the scene-referred, linear, camera RGB part of the pixel pipeline, before the input color profile is applied. However, the conversion from camera RGB to CIE Lab 1976 space relies on the input color profile. All of the lightness L metrics given in the spot mapping settings will use the input profile defined later in the input color profile module to perform the conversion accurately, but the conversion itself assumes a linear (RAW) signal and will not work for JPEG and PNG images (which are non-linearly encoded before the input color profile module). If you want to use this feature on non-RAW images, you will need to move the exposure module to after input color profile or to use the module order preset v3.0 for JPEG/non-RAW input.
Nota 3: A correspondência perfeita da sua amostra de controle com a luminosidade alvo pode ainda não produzir um resultado perceptivo semelhante, mesmo que os números sejam exatamente os mesmos. Por exemplo, se o seu assunto estiver na frente de um fundo feito de algumas partes claras e algumas partes escuras, a proporção de áreas claras/áreas escuras afetará a percepção de contraste e brilho. Se essa proporção mudar em sua série, o brilho do assunto não parecerá constante, mesmo que o valor de luminosidade seja exatamente constante. Para obter mais detalhes, consulte a ilusão da sombra do verificador e a ilusão de Chubb .